Видео

You got paid for this . This is the worst lock on the market . Most expensive and easiest to get of for thieves.

Is it normal that lockpin goes in raffly 40mm before got contact with flexplate?

i live in new england, both of my e36s have 240k miles on the chassis with zero rust, my 95 m3 just has a tiny little bit of surface rust on the jack point from a scratch but it only took 5 minutes to fix.

Is it safe to remove flywheel lock to drop down pistons 16’mm? Its part about timing

I just installed these exact lights today to my 2021 Honda Civic Sedan (Sport). Thanks to your tutorial, I was able to safely, efficiently, and successfully installed them with little to no issues at all. Keep up the amazing work! 🙌🏻✨

Very nice review of what's needed. Thinking about using an M52/M50 block bored to 86.5 as a base for a turbo motor for my e36 m3. Was there any discussion on milling or balancing the crankshaft? I'm just going through your back catalog so maybe I will find it later on.

I know this was 6 years ago. But those led bulbs with large COB led chips are the worse ones. I’m sure nowadays we got way better led hulb technology that performs better. Go for Lasfit

Advancelocks I believe that these are pretty great and bulletproof but obviously if you have enough time or in a shop with tools then the story changes. But it’s obvious that their sponsor of this guys the only question is is there any flaw in the locking mechanism ? Which can be its breaking point? Only time will tell

My set skips 12mm. SMH 😮‍💨

I think I'll just take my e36 to a mechanic,but well done you certainly know your stuff

Fire hazard

On the outside of the Rimgard is a little notch ~ if you look closely that "notch" is what you're supposed to line up to the lug nut hole, matching where you turned the lines of the inside locking mechanism. The outside notch is right by your finger, if you pause @ 8:56

Can you do an update?

Great video, thank you for this content.

I need one for my trd pro

Thanks man, super helpful

if you guys are going to consistently drive your car hard after going FI don't overlook cooling system upgrades (aluminum radiator and expansion tank ect..) braking, and suspension upgrades (control arms, bushings, motor and trans mounts, guibo disc ect..)

Can't I just stick a flathead screwdriver 🪛 into the keyhole and just turn it?

This and others of your videos were very helpful in guiding me on tearing down the top end of my 92 325is to replace the head gasket. Not sure if you're willing to answer some questions, but now that it's back together, I'm trying to figure out why the temp gague rises to the red after only a few minutes from a cold start. New thermostat, new water pump, ne temp sensor, new overflow tank.

Very nicely done video. Thanks for producing this.

Whered you go???!

Personally I prefer how halogens look for the interior, gives it a “warmer” or “cozier” feel. I would strongly recommend getting good LEDs and swapping out all of the lights on the back of the car, they look so much better

I did see this wheel lock broken and removed on another channel that tests wheel locks. There were no wheel locks that couldn't be defeated, it was a matter of how much time it took and these did take longer than others, so it's not a bad choice. Just like all locks, they are all defeatable it's about the difficulty level of the breach and time. The longer it takes the more of a deterrent it is. Criminals are lazy opportunists and unless they really need something, they will move on to easier prey.

There’s no need to take the little mudflaps that are underneath the fog lights off that panel will come down with those left attached to it

Gg good video

Im new to this world of short shifters, and all i want to know is, if it's suitable whit other vehicle or only with Honda civics.

Dude is thorough, great job bro!

Very impressive! Thank you.

No more uploads? 😢

what downpipe would go with that exhaust

That turned out way better than I thought it was going to.

That lock is crap. Mine got stolen with just a crowbar from the sides

is there any difference on an e34 m50b25? noticed on some kits it only lists compatibility with e36

This video is great, all business. I’m doing a head gasket replacement on my 98 single Vanos 328i. Thanks for all the tips. I’m rebuilding my Vanos, upgrading the cooling system, converting to electric fan, and replacing my heater control valve while I’m there.

I'm asking everywhere i can before taking to much apart on my 92 325is and hope you might be able to answer a question. To replace worn and brittle timing chain guide rails (the one operated by the plunger type tensioner on the side of the cylinder head), do you need to take off the tmobile chain front cover?

Joe Biden voting fk boy wearing a mask outdoor 😂

I'm never going to install one of these nor have a car that would take one - but that is a thing of beauty. I could feel the satisfying positive "donk" from here... England - because we like manual cars :)

Thank you

Currently building an M52B28. Hopefully should be done tomorrow! Video sure helped me with getting the head prepared to be removed tomorrow. Not my first time but I always refer here for refreshers 🤝🏼

Explicação muito boa

Show lindo

Loved hearing your experience and the BTS. What is your best recommend settings for those kind of hyperlapse shots? Timelapse or time shift?

Can somebody clarify something for me.... is this vanos housing aluminum? Or what material is this vanos housing made off?

Those locks are trash and overprived. Can be opened in 5 seconds with a pry bar. Look up the videos

You got scammed man, this thing take no time to defeat. Search video here.

Hey @pawinning I just finished my turbo bottom mount e36 Garrett gt3582 spa manifold build. I found motor teardown videos very helpful. Rebuilt my motor. It took almost a year way longer than I thought it would. Also upwards of 20k probably well over 5k mistakes but I learned a lot and did it. Was my first time doing motor work. I’ve always shied away from the motor but did a lot of suspension diff and anything but the motor lol.

Ooohh daaaayum! That looks so good!! And THANK YOU! for actually showing HOW you installed the lip! Can't find any vids that show the installation!

Do you use a external mic for the exhaust sounds ,if yes wich one or is the internal mic good enough

Try to do a DP/FP combo for the Si.

Pherable tune is amazing! I’m running MAP 2 with FMI with charge pipes from PRL, SRI from PRL and PRL RMM with stage 2 acuity SS kit. And the whole care feels amazing!!